Gauging the Gauge seems to need a Genie

Skipping the increase row just before starting the chart, and maintaining the chart pattern, works fine. Posting a pic of the work done so far. Thank you all for your suggestions and support !

I figured that the instruction as stated below, after the first 9 rows, before the chart,

resume working in the round as foll:

Next (inc) rnd *K9, M1; rep from * to end of rnd—120 sts.

essentially points to the row 7 of the chart which has the M1 increase at the end. The designer has not marked this as Row 10, for instance. Just says next inc row which is the row 7 of the chart. The mistake the designer made was to say K9, which threw us off.

All is well that ends well ! (Well, not yet …:smiley:

1 Like

Looks terrific with very pretty lace! Thanks for letting us see the progress so far.

1 Like

It just shows how a relatively small error, or the order of words in a pattern, can lead to a lot of confusion. Patterns really do need a good amount of editing and checking.

Your knitting looks great, I’m glad you manabed to resolve the problem and go ahead.

1 Like

All is not well …….. not yet :smiley:

Two more erratas found :

Remember, we concluded that skipping the M1 in the round just before the lace chart began would mean I needed to do an extra row 78 of the lace chart ? That would get me to 288 stitches.

Well, it happens that a M1 of row 77, is missing from the notations, while the chart does show that extra knit. That meant, I stuck to finishing with Row 77, and got to the 288 stitches as expected (but not instructed :squinting_face_with_tongue:) by the pattern.

And then the separation into the body and sleeves. And onto Lace chart 2 for the body.

The lace chart 2 repeats are set by The following two rounds :

Begin Lace Pattern 2 Charts :

Working appropriate chart for size, cont as foll:

Next rnd K2, work rnd 1 of lace patt 2 chart 4

times, k4, work rnd 1 of lace patt 2 chart 4

times, k2.

Next rnd K2, work rnd 2 of lace patt 2 chart 4

times, k4, work rnd 1 of lace patt 2 chart 4

times, k2.

Cont as now established, working rnds 3–36 once, then rnds 17–36 twice more.

the one in italics above should be rnd 2 :face_holding_back_tears:

Mindless knitting meant I had to frog full two rounds before I realised it. Shows how mindful one needs to be. Also told me that, thanks to the help especially from @Creations and @salmonmac over the last two years, I have grown a bit - to be able to read a pattern better, to imagine the outcome and to recognise the mistakes. Thank you for enriching my journey :heart_eyes:

2 Likes

This pattern sounds like a test, and you are passing with flying colours! Good spot on the errors!
Are you able to send the errors to the designer for them to list with the pattern?

1 Like

Once you find an error your trust in the pattern plummets and you second guess each direction. It shouldn’t be this frustrating.
You’ve done a terrific job figuring ways around the errors. Good for you for persisting on this lovely sweater.
Yes, letting the designer know or posting on the Ravelry comments is helpful.
https://www.ravelry.com/patterns/library/lacey-cable-cardigan

2 Likes

That is a great idea. Will certainly do so, once I finish the knit.

Tried to contact her earlier but didn’t get a response, perhaps because this pattern was published a long time back in the Noro magazine. (although we are connected on Instagram)

Thank you so much !

Will certainly do so on Ravelry as well.

Thank you so much !

I was overly optimistic about the lace 2 chart, I think.

What is emerging is nothing like the original :astonished_face:

The center stitch of the 24 stitch repeat seems to be at the perfect location. I wonder why the rest of the lace looks so different from what it should be.

Would you post a photo of your knitting? Possibly we can figure out what’s going on.

1 Like

Here are the original pic, lace 2 chart and my knitted piece, @salmonmac. I have done the first 7 rows of the chart,

That alignment and pattern look right to me. Here’s a cropped photo from the details page:

It may be that there’s missing or shifted yarn overs here (red circle) but you can check it by spreading out the lace to make sure.

1 Like

Thank you @salmonmac, for taking the trouble to check this for me.

Perhaps once blocked the lace will look better.

I will have a relook at the part you have highlighted.

Many thanks !

1 Like

The knitting looks lovely. It’s going to be such a pretty sweater. Worth the effort for sure!

1 Like